Page 1:ViewSonic VP2772: 27", 2560x1440, 10-Bit Colour, And Adobe RGB
Page 2:Packaging, Physical Layout, And Accessories
Page 3:OSD Setup And Calibration Of The ViewSonic VP2772
Page 4:Measurement And Calibration Methodology: How We Test
Page 5:Results: Brightness And Contrast
Page 6:Results: Grayscale Tracking And Gamma Response
Page 7:Results: Colour Gamut And Performance
Page 8:Results: Viewing Angles And Uniformity
Page 9:Results: Pixel Response And Input Lag
Page 10:A Pro Monitor That Delivers The Last One-Percent
Results: Viewing Angles And Uniformity
The more monitors we test, the more we can see that off-axis viewing performance is dependent not only on pixel structure (IPS, PLS, TN, etc.), but backlight technology as well. The anti-glare layer makes a difference, too.
I've reviewed two other GB-r-LED displays, Asus’ PA279Q and Dell’s UP2414Q. Both showed a distinct red shift to the sides and a subtle blue shift in the vertical plane. But ViewSonic's VP2772 has the best horizontal off-axis image I've ever seen. There is practically no light falloff and no visible colour change either. Even the red tint in the top and bottom photos is minimal. You can easily see the darkest three gray bars, meaning gamma and black levels are not significantly compromised. If you’re doing colour-critical work on this panel, you won’t have to lock your head to the center of the screen to maintain visual accuracy.
Screen Uniformity: Luminance
In order to gauge screen uniformity, zero- and 100-percent full-field patterns are used, and nine points are sampled. We continue comparing the results to other monitors we’ve reviewed, too.
First, we establish a baseline result at the center of each screen. Then the surrounding eight points are measured. Their values get expressed as a percentage of that the baseline figure, either above or below. This number gets averaged. It is important to remember that we only test the review sample each vendor sends us. Other examples of the same monitor may measure differently.
First up is black field uniformity.
Some professional-class displays offer uniformity compensation, but not the VP2772. We always see a reduction in contrast when it’s turned on, so that feature is not missed in today's story; the uncorrected numbers are fine by us.
Raw measurements cover a .0512 cd/m2 range from high to low, which is imperceptible. The meter does say there's a slight hotspot in the center of the screen, though.
Here’s the white field measurement:
White field uniformity is also under our 10-percent standard, and we can't see any variations in tone here, either. Again, the brightest part of the panel, according to our C6 meter, is in the center.
Screen Uniformity: Colour
To measure colour uniformity, we display an 80-percent white field and measure the Delta E error of the same nine points on the screen. Then we subtract the lowest value from the highest to arrive at the result. A smaller number means a display is more uniform. Any value below three translates to a variation that is invisible to the naked eye.
Colour uniformity from the VP2772 isn't as good as some of the other monitors we've tested. There's a faint green tint on either side of the center, and an even fainter red hue in the lower-right corner. Observing this phenomenon in actual content is difficult (a white field pattern is an extreme test). But if you are sensitive to the issue, consider finding a dealer that will let you hand-pick your monitor, since every sample will be different.
- ViewSonic VP2772: 27", 2560x1440, 10-Bit Colour, And Adobe RGB
- Packaging, Physical Layout, And Accessories
- OSD Setup And Calibration Of The ViewSonic VP2772
- Measurement And Calibration Methodology: How We Test
- Results: Brightness And Contrast
- Results: Grayscale Tracking And Gamma Response
- Results: Colour Gamut And Performance
- Results: Viewing Angles And Uniformity
- Results: Pixel Response And Input Lag
- A Pro Monitor That Delivers The Last One-Percent