Page 1:ViewSonic VP2772: 27", 2560x1440, 10-Bit Colour, And Adobe RGB
Page 2:Packaging, Physical Layout, And Accessories
Page 3:OSD Setup And Calibration Of The ViewSonic VP2772
Page 4:Measurement And Calibration Methodology: How We Test
Page 5:Results: Brightness And Contrast
Page 6:Results: Grayscale Tracking And Gamma Response
Page 7:Results: Colour Gamut And Performance
Page 8:Results: Viewing Angles And Uniformity
Page 9:Results: Pixel Response And Input Lag
Page 10:A Pro Monitor That Delivers The Last One-Percent
Results: Grayscale Tracking And Gamma Response
A majority of monitors, especially newer models, display excellent grayscale tracking (even at stock settings). It’s important that the colour of white be consistently neutral at all light levels from darkest to brightest. Grayscale performance impacts colour accuracy with regard to the secondary colours: cyan, magenta, and yellow. Since computer monitors typically have no colour or tint adjustment, accurate grayscale is key.
The VP2772 only offers grayscale adjustments in the User Color mode. For reasons that you'll see on the next page, you simply cannot use that setting for colour-critical applications. If you don’t mind oversaturated reds, however, you can adjust grayscale to a very accurate level.
There's a lot to like about the results I measured. Not only are the errors invisible to the naked eye, but only 10-percent brightness tops one Delta E. All it took to achieve this was a two-click reduction in green. The average error is .77 Delta E.
When you’re in the Adobe RGB mode, you can’t adjust the RGB values. That's not an issue, though.
A professional monitor shouldn’t require calibration, and ViewSonic's VP2772 doesn’t. The above chart represents 200 cd/m2, but we got pretty much the same results at 50 and 120 cd/m2. This is excellent out-of-box performance. You're going to pay a premium of course, but if accuracy is important, the VP2772 delivers.
Again, here's how the comparison group fares:
As ViewSonic's monitor is shipped, expect a 1.51 Delta E in Adobe RGB mode with the brightness maxed. That’s well below the generally-accepted threshold of three Delta E. Literally, all you have to do is unpack the VP2772 and turn it on. The only adjustment needed is setting your preferred light output level.
At 200 cd/m2, the error is a tiny bit lower.
Nobody will tell the difference between 1.51 and 1.43 Delta E. And we recorded similar results at 120 and 50 cd/m2. If you want greater accuracy, the User Color mode facilitates it, albeit with compromised gamma and colour gamut values.
Gamma is the measurement of luminance levels at every step in the brightness range from 0 to 100 percent. It's important because poor gamma can either crush detail at various points or wash it out, making the entire picture appear flat and dull. Correct gamma produces a more three-dimensional image, with a greater sense of depth and realism. Meanwhile, incorrect gamma negatively affects image quality, even in monitors with high contrast ratios.
In the gamma charts below, the yellow line represents 2.2, which is the most widely-accepted standard for television, film, and computer graphics production. The closer the white measurement trace comes to 2.2, the better.
This is the gamma trace from the User Color mode. It isn’t bad, but does trend low as brightness increases. When the measurement falls below the yellow line, those levels are too bright. Ideally, you want a flat trace from bottom to top. The image loses just a little pop in the mid-tones, as well as in highlights. The maximum error is at 70 percent, where light output is 8 cd/m2 above the target.
Gamma in Adobe RGB mode isn’t perfect, but it’s far better.
Once again, the culprit is 70 percent with a 4.5 cd/m2 error. The rest of the trace is quite a bit flatter, at least. This chart reflects the Standard preset. The other two options, Gentle and Steep, show the same line either below or above our target.
A .15 deviation represents tight tracking. All of the monitors in this group fare really well though, and none demonstrate gamma issues that'd cause us concern.
We calculate gamma deviation by simply expressing the difference from 2.2 as a percentage.
The average value of the Standard preset is a little low at 2.14. The numbers range from 2.06 to 2.21, and that's still solid performance. If you want a punchier image, select the Steep option and turn up the brightness a few clicks. It won’t be as true to most content, but you'll get a little extra depth.
- ViewSonic VP2772: 27", 2560x1440, 10-Bit Colour, And Adobe RGB
- Packaging, Physical Layout, And Accessories
- OSD Setup And Calibration Of The ViewSonic VP2772
- Measurement And Calibration Methodology: How We Test
- Results: Brightness And Contrast
- Results: Grayscale Tracking And Gamma Response
- Results: Colour Gamut And Performance
- Results: Viewing Angles And Uniformity
- Results: Pixel Response And Input Lag
- A Pro Monitor That Delivers The Last One-Percent