Thermaltake Toughpower DPS G RGB 850W PSU Review

Load Regulation, Hold-Up Time, And Inrush Current

To learn more about our PSU tests and methodology, please check out How We Test Power Supply Units. 

Loading...

Primary Rails And 5VSB Load Regulation

Load Regulation testing is detailed here.

Hold-Up Time

Our hold-up time tests are described in detail here.

The hold-up time is a little lower than required, while the power-good signal's time is significantly lower than the ATX specification's minimum. At least that signal is accurate, since it drops before the rails go out of spec.

Inrush Current

For details on our inrush current testing, please click here.

The inrush current levels are normal with both voltage inputs (115V and 230V).

Load Regulation And Efficiency Measurements

The first set of tests reveals the stability of the voltage rails and the TPG-0850D-R's efficiency. The applied load equals (approximately) 10 to 110 percent of the PSU's maximum load in increments of 10 percentage points.

We conducted two additional tests. During the first, we stressed the two minor rails (5V and 3.3V) with a high load, while the load at +12V was only 0.1A. This test reveals whether a PSU is Haswell-ready or not. In the second test, we determined the maximum load the +12V rail could handle with minimal load on the minor rails. 

Test #12V5V3.3V5VSBDC/AC (Watts)EfficiencyFan Speed
Fan Noise
Temps (In/Out)PF/AC Volts
15.216A1.983A1.979A0.996A84.7886.71%0 RPM
0 dB(A)
50.86°C0.975
12.114V5.042V3.333V5.017V97.7839.68°C115.1V
211.480A2.979A2.981A1.201A169.6590.09%0 RPM0 dB(A)51.83°C0.990
12.090V5.023V3.318V4.995V188.3140.02°C115.1V
318.129A3.497A3.505A1.405A254.8690.78%536 RPM22.4 dB(A)42.21°C0.994
12.067V5.009V3.307V4.977V280.7453.53°C115.1V
424.790A4.005A4.005A1.610A339.7090.82%536 RPM22.4 dB(A)42.51°C0.996
12.042V4.994V3.294V4.960V374.0354.37°C115.1V
531.104A5.021A5.029A1.821A424.5890.48%536 RPM22.4 dB(A)42.90°C0.997
12.028V4.973V3.280V4.939V469.2857.39°C115.1V
637.106A6.055A6.060A2.030A509.5089.83%544 RPM22.5 dB(A)44.23°C0.997
12.120V4.954V3.267V4.917V567.1761.63°C115.1V
743.408A7.093A7.105A2.245A594.4488.99%804 RPM29.6 dB(A)44.70°C0.998
12.103V4.933V3.251V4.894V667.9763.64°C115.1V
849.753A8.148A8.157A2.460A679.3888.28%804 RPM29.6 dB(A)46.39°C0.998
12.079V4.913V3.236V4.873V769.5866.71°C115.1V
956.560A8.680A8.719A2.464A764.4387.54%884 RPM30.0 dB(A)46.50°C0.998
12.055V4.899V3.223V4.861V873.2867.42°C115.1V
1063.127A9.220A9.252A3.106A849.1886.47%1084 RPM35.8 dB(A)47.42°C0.998
12.031V4.882V3.210V4.826V982.0868.61°C115.1V
1169.480A9.242A9.276A3.113A924.1085.64%1324 RPM40.9 dB(A)47.89°C0.998
12.009V4.871V3.202V4.816V1079.0769.42°C115.1V
CL10.099A16.025A16.004A0.004A132.1581.94%536 RPM22.4 dB(A)44.00°C0.988
12.100V4.910V3.265V4.991V161.2864.33°C115.1V
CL270.789A1.003A1.003A1.002A864.3486.92%1172 RPM38.5 dB(A)48.93°C0.998
12.024V4.957V3.248V4.933V994.4071.04°C115.1V

The load regulation on the +12V rail is pretty tight. In comparison, the minor rails—including 5VSB— have loose regulation, which falls outside of the 3% region. It is worth mentioning that the +12V rail has a strange voltage increase in the 60% load test, something that we rarely see in our tests. The resonant controller appears to perform this change in order to keep regulation in order, and the trick keeps the rail within 1%, achieving good overall performance.

Up to the 20% load test, Thermaltake's TPG-0850D-R operates in passive mode. It's only during a very stressful scenario that includes full load delivery under a high ambient temperature that the fan's speed increases enough to make a noticeable noise. The 40 dB(A) mark is exceeded during the overload test, where the PSU is pushed beyond its official limits. In general, the fan profile is very loose and offers quiet operation.

When it comes to efficiency, Thermaltake narrowly misses the 87% mark during our 20% load test, while with mid-load it is over the desired 90%. However, under full load it scores less than 87% efficiency. In a normal environment this PSU should have no trouble meeting the 80 PLUS Gold requirements, though we've seen Gold-rated units register much higher efficiency levels.

DPSApp Screenshots

You will find several screenshots of the DPSApp software below.

The provided efficiency readings aren't accurate enough; the same goes for the voltage readings, especially under high loads. On the other hand, the output wattage readings are quite accurate, so the problem looks to be in incoming power (the power that the PSU draws from the wall socket) measurements.

This thread is closed for comments
12 comments
    Your comment
  • powernod
    -It's not exactly a PSU-related question but more likely a general one.
    From the pictures from the monitoring software, i can notice that this software is able to measure CPU and GPU temperature. Do you have any idea if such monitoring is (relatively) accurate?
    -Excellent review Aris !!
  • Malik 722
    in corsair link software atleast both cpu and gpu temperatures are accurate.
  • Aris_Mp
    it takes readings from the system's (actually the individual components') sensors. If those are accurate then the software's readings will be accurate as well. Normally they are accurate.
  • Nuckles_56
    That 12V transient response was certainly interesting, I don't think I've seen one do anything like that before
  • turkey3_scratch
    1670073 said:
    That 12V transient response was certainly interesting, I don't think I've seen one do anything like that before


    Do what?
  • Nuckles_56
    1712875 said:
    1670073 said:
    That 12V transient response was certainly interesting, I don't think I've seen one do anything like that before
    Do what?


    Go and plummet back down to almost 0V during the test
  • turkey3_scratch
    1670073 said:
    1712875 said:
    1670073 said:
    That 12V transient response was certainly interesting, I don't think I've seen one do anything like that before
    Do what?
    Go and plummet back down to almost 0V during the test


    I don't think you're reading the transient response graph properly. It's not a measure of voltage but a measure of ripple (well, technically that is a measure of voltage but it's more a measure of instantaneous offsets of an average, or a highly zoomed in sector).

    That or I am just missing something. I probably am. Not sure what I'm missing though. Forgive my ignorance.
  • Aris_Mp
    yes this is something really weird indeed.
  • sparkyman215
    Fantastic review Aris! I absolutely love reading in depth articles about anything. Terrible PSU for the price, but it's an awesome review. Congrats!
  • turkey3_scratch
    1670073 said:


    Oh you mean turn-on transient not transient response ;)
  • Nuckles_56
    1712875 said:
    1670073 said:
    Oh you mean turn-on transient not transient response ;)


    Oops, my bad :lol: