Display Calibration 101: Step-By-Step With Datacolor's Spyder4Elite

Spyder4Elite How-To: Overview

Now you should see patterns being displayed underneath the Spyder4 sensor. Unless you picked the Native brightness option on the Choose Settings screen, the calibration will pause somewhere towards the beginning of the process, and you’ll be asked to adjust your monitor’s brightness control until it reaches within four percent of your chosen brightness level.

The Target brightness setting is displayed in the upper right-hand corner, directly above the Current reading. If the current reading is higher than the target setting, lower the brightness control on your monitor. Alternatively, if the current level is lower than the target, raise the brightness.

After making an adjustment, click Update and check the new current reading against the target. If necessary, repeat this process until you come as close to the target setting as your monitor’s brightness control will allow. When done, click Next to continue the calibration process.

When the status bar has filled up and the screen reads Measuring Completed, you can remove the Spyder4 senor from the screen and click Finish.

Save

Now that the calibration process is complete, you can choose to name and save your calibrated monitor profile, as well as set up regular recalibration reminders.

When you're finished, click Save and then Next.

View Calibration: SpyderProof

With your work saved, you can compare your monitor’s calibrated and uncalibrated state using the SpyderProof utility. The Switch button in the lower right-hand side of the Spyder4 screen changes between calibrated and uncalibrated modes.

The checkerboard of images provides a good cross-section of typical content. The difference in white balance can be easily seen in the four black and white pics in the lower right.

View Calibration: SpyderTune

The SpyderTune button in the upper right-hand corner switches between the SpyderProof and SpyderTune utilities.

In SpyderTune, you can tweak the white point, gamma, and brightness using on-screen sliders to the right of the checkerboard demo. You can immediately see the effect of these adjustments on the output. If you don’t care for any of you own adjustments, simply click Reset to go back to the calibrated settings. If you do want to commit any changes, just click Save.

When done making any post-calibration adjustments, click Next.

Create a new thread in the UK Article comments forum about this subject
This thread is closed for comments
14 comments
Comment from the forums
    Your comment
  • Menigmand
    I still don't understand why we have to buy a $250 device just to get a proper picture on our screens. Why are they not factory calibrated? After all, in these days, the input is digital, so the display data should be 1-to-1 identical to (for example) game RGB data... I'm sure I'm wrong somehow, but about what?
  • mi1ez
    That was actually a genuinely interesting article! Good work Tom's.

    885869 said:
    I still don't understand why we have to buy a $250 device just to get a proper picture on our screens. Why are they not factory calibrated? After all, in these days, the input is digital, so the display data should be 1-to-1 identical to (for example) game RGB data... I'm sure I'm wrong somehow, but about what?


    The problem is twofold:

    Variance in the panels. Each panel would need to be calibrated individually adding time and cost

    The WOW factor. Many manufacturers will ship monitors with the saturation set too high so when you fist set it up it gives you the wow factor. I believe. This second one might not be 100% true and more of a showroom trick.
  • Will P
    A great article, a good introduction on an often overlooked aspect of the PC setup. Every screen I have ever bought has had a ridiculously high brightness out of the box, which I suppose could be put down to a 'Wow factor' for sure... The kit is expensive though, but if it is going to make every screen you own 20% better and last for 5 years it starts to look like a good investment.

    I was wondering if the re-calibration of the cheaper units (such as the Spyder) can be done with the Spyder itself or do you need specialist kit?
  • timbozero
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it.
    There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost.
    Was the author sponsored by DataColor or, just wildly out of touch?
  • mi1ez
    249904 said:
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it. There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost. Was the author sponsored by DataColor or, just wildly out of touch?

    How does a blu-ray calibrate a screen then?
  • timbozero
    142373 said:
    249904 said:
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it. There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost. Was the author sponsored by DataColor or, just wildly out of touch?
    How does a blu-ray calibrate a screen then?


    Is short (for the example I mentioned) , you get several display patterns shown and adjust your screen until they display as they should. You will need to do this a few times for each as some will impact others (you would have to with the Datacolor as well unless it can adjust your monitor automatically afaik). The colours are adjusted the same way but with a filter used by you to help 'understand' the data.

    This is a link to typical testcard used by the Blu-Ray http://www.blu-ray.com/movies/screenshot.php?movieid=16216&position=2
    This is a link to a review of the Blu-Ray on the same site http://www.blu-ray.com/movies/Disney-WOW-World-of-Wonder-Blu-ray/16216/

    Hopefully that will help
  • mi1ez
    249904 said:
    142373 said:
    249904 said:
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it. There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost. Was the author sponsored by DataColor or, just wildly out of touch?
    How does a blu-ray calibrate a screen then?
    Is short (for the example I mentioned) , you get several display patterns shown and adjust your screen until they display as they should. You will need to do this a few times for each as some will impact others (you would have to with the Datacolor as well unless it can adjust your monitor automatically afaik). The colours are adjusted the same way but with a filter used by you to help 'understand' the data. This is a link to typical testcard used by the Blu-Ray http://www.blu-ray.com/movies/screenshot.php?movieid=16216&position=2 This is a link to a review of the Blu-Ray on the same site http://www.blu-ray.com/movies/Disney-WOW-World-of-Wonder-Blu-ray/16216/ Hopefully that will help


    So do you have like a physical card to compare with what's on screen?
  • timbozero
    142373 said:
    249904 said:
    142373 said:
    249904 said:
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it. There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost. Was the author sponsored by DataColor or, just wildly out of touch?
    How does a blu-ray calibrate a screen then?
    Is short (for the example I mentioned) , you get several display patterns shown and adjust your screen until they display as they should. You will need to do this a few times for each as some will impact others (you would have to with the Datacolor as well unless it can adjust your monitor automatically afaik). The colours are adjusted the same way but with a filter used by you to help 'understand' the data. This is a link to typical testcard used by the Blu-Ray http://www.blu-ray.com/movies/screenshot.php?movieid=16216&position=2 This is a link to a review of the Blu-Ray on the same site http://www.blu-ray.com/movies/Disney-WOW-World-of-Wonder-Blu-ray/16216/ Hopefully that will help
    So do you have like a physical card to compare with what's on screen?


    No, the only physical item (other than the disc) is a blue tinted filter which is used for one of the several tests.
    Brightness (as an example) displays a test strip and you adjust the brightness until your screen shows certain details but not others (as instructed by the previous 'chapter' of the 'film').
    There are several levels of testing and reading the review I linked will give you more of an idea.

    I did the setup for TV, projector setup (Datacolor products won't work on projectors as the device blocks the very image you need to measure) and my monitor. The projector wasnt far out and made a small difference, my monitor and TV were 'miles' out and the tuning with the disc worked wonders :)
  • mi1ez
    249904 said:
    142373 said:
    249904 said:
    142373 said:
    249904 said:
    It is IMO ridiculous to suggest the spending of near the cost of a monitor to calibrate it. There are several Blu-ray Discs (Disney World of Wonder for example) that will achieve 80%+ of the levels of calibration for 10% of the cost. Was the author sponsored by DataColor or, just wildly out of touch?
    How does a blu-ray calibrate a screen then?
    Is short (for the example I mentioned) , you get several display patterns shown and adjust your screen until they display as they should. You will need to do this a few times for each as some will impact others (you would have to with the Datacolor as well unless it can adjust your monitor automatically afaik). The colours are adjusted the same way but with a filter used by you to help 'understand' the data. This is a link to typical testcard used by the Blu-Ray http://www.blu-ray.com/movies/screenshot.php?movieid=16216&position=2 This is a link to a review of the Blu-Ray on the same site http://www.blu-ray.com/movies/Disney-WOW-World-of-Wonder-Blu-ray/16216/ Hopefully that will help
    So do you have like a physical card to compare with what's on screen?
    No, the only physical item (other than the disc) is a blue tinted filter which is used for one of the several tests. Brightness (as an example) displays a test strip and you adjust the brightness until your screen shows certain details but not others (as instructed by the previous 'chapter' of the 'film'). There are several levels of testing and reading the review I linked will give you more of an idea. I did the setup for TV, projector setup (Datacolor products won't work on projectors as the device blocks the very image you need to measure) and my monitor. The projector wasnt far out and made a small difference, my monitor and TV were 'miles' out and the tuning with the disc worked wonders :)


    It's very much subjective still, rather than absolute. While I agree for most people this is pointless, if you need it calibrated you need it done properly. I wouldn't surprised if you could rent one of these if you looked hard enough.
  • timbozero
    It is not at all subjective, you need to use it to realise that it is 'absolute' but, it is not as accurate as digital metering (only close to).
  • mi1ez
    249904 said:
    It is not at all subjective, you need to use it to realise that it is 'absolute' but, it is not as accurate as digital metering (only close to).


    If you're using your eyes, then it is subjective. You can't say that everyone's eyes are the same, 20/20 or not.
  • timbozero
    *sigh* Think how you will , I am not here to change your mind.

    The brightness test (for example) is done with a graduated display thus :-
    http://static.highdefview.com/wp-content/uploads/review/wow/wow_brightness_thumb.jpg.pagespeed.ce.JIxKCdd3ek.jpg
    There is only 1 point on the brightness adjustment where the correct graduation will match and the only 'downside' (which you could even remotely call subjective) is that it will not be spot on (as a digital meter might be).

    There is another for contrast etc., etc., etc.. Once they are all completed .....

    Ah hell, try it or don't. It made a massive difference to my cinema room and for only 25$ which is a bargain compared to the digital meter (which was my initial point, that it's overkill to buy a meter)

    Peace, Out :)
  • mi1ez
    249904 said:
    *sigh* Think how you will , I am not here to change your mind. The brightness test (for example) is done with a graduated display thus :- http://static.highdefview.com/wp-content/uploads/review/wow/wow_brightness_thumb.jpg.pagespeed.ce.JIxKCdd3ek.jpg There is only 1 point on the brightness adjustment where the correct graduation will match and the only 'downside' (which you could even remotely call subjective) is that it will not be spot on (as a digital meter might be). There is another for contrast etc., etc., etc.. Once they are all completed ..... Ah hell, try it or don't. It made a massive difference to my cinema room and for only 25$ which is a bargain compared to the digital meter (which was my initial point, that it's overkill to buy a meter) Peace, Out :)


    We'll agree to disagree.
  • Flyfisherman
    Very interesting and much needed article, keep up the good work!

    But there is one thing that comes in mind, about the licence of the S/W.
    Is it possible to install the S/W and the colorimeter on more than one computer, or is it locked to the first computer once one has entered the activation code?

    Because I have several computers at home and really would like to use the equipment to do this calibration on them all.

    I assume that there should not be a problem to calibrate two monitors on the same computer?

    Best Regards from Sweden.