mean:it 5PM EATX Mid-Tower Case Review

Premium cases have capitalized on the look of tempered glass to exude class, and it didn’t take long for budget companies to catch on, yet most of those cases have glass on only one side. The added cost associated in additional panels (pricier shipping, increased damage risk) had been borne by only a few budget-minded companies, and none of those have yet produced a case with three glass panels for under $100. Enter the 5PM from mean:it (aka meanit).

With three LED fans up front and enough room for true EATX motherboards (including the provision of extra standoffs), the 5PM shoots straight for the market previously assumed by the award-winning Cullinan. The mean:it sample comes at a lower price, and that builds our anticipation for yet another example of value leadership. But we must test it first!


Keen eyes will notice that it’s possible to see right through the empty 5PM, thanks primarily to the large hole in its motherboard tray that allows CPU cooler support plates to be installed on the backs of most already-mounted motherboards. Those who can’t see this might need to adjust their monitors, though the dark tint of two panels together forces one to look more closely.

Front-panel ports face upward from the top edge and include two USB 3.0, two USB 2.0, and headphone and audio jacks. The power button is capped in anodized aluminum and surrounded by a power indicator ring, while the likewise-capped reset button is surrounded by an HDD activity indicator ring. The fan controller has three buttons for off, low, and high, while the circuit board itself can be switched between PWM and DC mode.

In PWM mode, the “High” function reverts speed control to a motherboard fan header. We call this a two-speed controller since “off” isn’t technically a speed, but mean:it refers to the ability of high speed mode to function either as a PWM repeater or pass-through as two of three possible settings (low, high, auto, though switching between high and auto requires opening the case).

A look around back reveals the other glass side panel, eight slots, a 120mm fan mounted on slots to allow raising and lowering of its position, an additional set of screw slots for 140mm fan upgrades, seven expansion slots, and a single-screw slide cover for the extremely narrow expansion card tab opening.

A power supply dust filter slides out from the back edge of the bottom panel to ease maintenance. This is the 5PM’s only intake filter.

The 5PM’s three 120mm intake fans are mounted on adapters, between the front panel of the metal chassis and plastic-framed glass fascia. Additional fan mounts are found behind these adapters.

Those additional fan mounts support three 140mm or 120mm fans and/or radiators. Space at the top is limited to 17.5” by front panel cables, while space behind the fan mounts is limited to a 2.4” gap between the front panel and power supply shroud. The front-mounted fan adapters make it possible to retain the factory fan configuration while installing a radiator of different size or spacing.

A plastic cable cover also seen above can be removed to make room for 13” deep boards, and a water pump mount is located in front of that cover on the power supply shroud.

Ventilation for front-panel fans is provided by slots behind the glass panel of the fascia.

The top panel holds 3x 120mm and 2x 140mm radiators up to 2.3” total thickness (including fans). The length is restricted to 16.3”, again by front-panel cables. Magnetic strips secure a mesh dust filter over this opening.

The 5PM has extremely little cable space behind the motherboard tray (approximately ½”), apart from an inward step around 14” from the back panel that opens it up another ½”. That inward step is why the case has a 14” motherboard depth limit in spite of its 17” supported card length. Three 2.5” SSD trays further limit space behind the motherboard.

Two additional trays support both 3.5” and 2.5” drives, with holes on the bottom for screw mounting of the smaller drives, and silicon-damped pins on the side to reduce the vibration of 3.5” drives.

The PWM-compatible 6-fan hub is factory connected to the three front-panel intake and single rear exhaust fans, leaving two open headers. The two four-pin PWM headers connect an input cable from the CPU fan header, and an output cable for the CPU fan.

MORE: Best Cases

MORE: All Case Content

Create a new thread in the UK Article comments forum about this subject
This thread is closed for comments
No comments yet
Comment from the forums
    Your comment