Fractal Design is once again at Computex. The Swedish-based company is well known for its cases, and at the industry's biggest show, it's adding two more to its roster, and it's also introducing a few upgrades to its entire group of water cooling products.
Two New Cases
Fractal Design has developed two mini-ITX PC cases for users who want high-performance parts in the smallest space possible.
One of the greatest difficulties of building a mini-ITX system is trying to get all the performance you want from a full desktop system in such a small confined space. The reduced form-factor creates a challenge in terms of fitting in certain physically larger components, such as PSUs and GPUs, and cooling the cramped space can be problematic.
To overcome these difficulties, cases like the new Fractal Design Core 500 do the only thing they can do: they extend the size of the case to allow larger components and allow more airflow. Though these cases are larger than the traditional mini-ITX form factor, they are still smaller than micro-ATX cases and can accommodate full-sized GPUs and many PSUs. They also promise better cooling.
This particular case was optimized for cooling. Inside is a pre-installed Fractal Design Silent Series R3 140mm rear exhaust fan, which should be relatively quiet while helping to cool the system. The case has sufficient space for large CPU coolers, supporting a cooler tower up to 170 mm in height, and supporting large 280 mm radiators for water cooling.
In addition, the case can hold plenty of drives for an mini-ITX case, including three 3.5-inch drives, three 2.5-inch drives, and one 5.25-inch drive simultaneously.
The case is expected to cost $59.99 when it hits the market, but no release date is set as of yet.
The company also has another mini-ITX case called the Node 202 which measures at 82 x 377 x 330 mm (HxWxD) and weighs a little over seven pounds. It has two 2.5-inch drive bays, two expansion slots, and two USB 3.0 ports in the front along with a headphone and mic jack. The maximum height for a CPU cooler it can accommodate is 56 mm, and the specs say there are two additional 120 mm fan placements in the graphics card chamber. Speaking of the graphics card, The Node 202 allows graphics up to 145 x 310 x 47 mm (HxLxD).
Aside from the chassis, the package also comes with three dust filters and a stand so you can place it in either the traditional horizontal position or free up space on your desk by placing it upright.
For power supplies, it's compatible with SFX variants up to 130 mm long. However, you can also purchase the case with an included SFX 450 W PSU from the company's Integra series. It's an 80 PLUS Bronze-rated model with two PCI-E 8-pin connectors, two SATA connectors, one ATX 24-pin (20+4) connector, and an ATX 12V 8-pin (4+4) connector.
The Node 202 and Integra SFX 450W combo will cost you $139.99, but if you already picked out a PSU, the standalone case will cost $79.99.
While these two cases both support the same motherboard form factor, the Node 202 is a smaller case than the Core 500. Building for the SFF crowd is no small feat, with the reduction of the interior space posing a big challenge to development. However, Fractal Design seemed to be able to make not one, but two more cases to add to two of its four case lineups.
Keep Your CPUs Cool
In addition to cases, the company also took some time and gave its water cooling products a few changes. The Kelvin series has three models: the S36 features three radiators with a total measurement of 30 x 394 x 397 mm (HxWxD), the S24 has two radiators and measures 30 x 124 x 275 mm (HxWxD), and the T12 only has one radiator with a measurement of 46 x 132 x 163 mm (HxWxD).
The first of the big changes is to mounting specs. Adding to its large list of supported sockets for both Intel and AMD processers, these updated coolers now support the 2011-v3 socket. The old fans were also swapped out for Dynamic GP-12 PWM fans, which apparently provides larger airflow and operates more quietly. The new fans also have speed variations between 500 and 2000 RPM. A low pump speed cable was also added to decrease sound, and the radiator screws are now replaced with PH2 heads. Additionally, the fill port for the pump now has a coin slot so you can access it without the need of an Allen key.
The final changes are a minute, but essential detail: A small groove is added to the bottom of the fittings, which should make it more difficult to accidentally remove the tubes. The tubes are also changed to have a slightly harder material, but it's unclear as to the specific material used.
The S36 will cost you $139.99, the S24 will cost $119.99, and the T12 is $99.99. With these upgrades and its ability to work with expansions to your water cooling build, the Kelvin coolers might be a considerable choice whether it's you're a water cooling rookie or veteran.
Options And Improvements
These latest offerings from Fractal Design continue to appeal to its loyal customers. The Node 202 and Core 500 should please the SFF crowd, and the updates to the Kelvin water cooling series show that the pursuit of cooler temperatures and quieter systems can always be improved.
We're going to see Fractal Design at Computex, so we're going to get a closer look at what the company has to offer for the latter half of the year.