[Solved] ASUS P8Z68-V PRO doesn't accept any RAM after RMA

That sounds plausible, but how does the motherboard determine if the RAM is OK or not? Does this involve communicating with the CPU against what is in the DRAM slots or does it have its own circuitry? The CPU functioned OK before I have gotten the motherboard fixed, only problems being the non standard configuration of RAM. Unless the bent pins have the ability to "reprogram"/fry the CPU, it should have been OK, right?

Also, I can't think of a simple way I could test the CPU in another system, or my system with another CPU, unless someone has suggestions?

"The cpu has an integrated memory controller, so obviously it involves communication between the cpu and ram"
1. I understand that the memory controller is integrated and all that jazz, what I would like to know is whether the motherboard turns on the DRAM light based on something it figures out or based on what the CPU tells it. That might help me pinpoint the issue. AFAIK, the board has its own circuitry for that.

"How could you possibly bend pins when installing the cpu, and not even know it?"
2. I had to correct this in my OP, but on the LGA1155 socket the pins are on the socket itself and not the CPU. The socket looks trippy when you look at it closely, as you can see here, so it is not immediately obvious that there is a bent pin. I am actually thinking that the motherboard was originally delivered damaged and I somehow did not notice the bent pins, not to mention the system worked to some capacity, so I didn't think much of it until later. That is how "you possibly bend pins when installing the cpu, and not even know it."

"Sounds like you were not very carfeful when installing the components and you possibly have a damaged cpu now."
3. The jury is still out on the CPU being damaged. I am yet to get any information that proves it to be so.

Just from reading this thread, I too am inclined to think that that there are bent pins on the CPU, or the CPU is damaged. Whether at fault of the OP or not, I cast my vote as well that there most likely lies the problem.

I got the replacement CPU today. (Intel shipped it overnight, wow.) The system still doesn't work for the same reason. Time to call, ASUS, again, I suppose.

I suppose I don't. I just hope I am not part of some sort of bad statistic where every new and replacement part I get is not functional.

I have this same issues on my ASUS P8Z68-V LX board with my new i5-2500k. My board will not post if the RAM is in dual channel mode. I can swap it to single channel with the same RAM and it works just fine. This is with 2x4GB of Patriot Viper Xtreme DDR3-1600 RAM.

My issue is different though. My board HAS POSTED with this very same RAM and CPU in dual channel mode. I had originally installed the stock CPU cooler while waiting for a new retention bracket for my Cooler Master V8. After receiving it, I installed the new CPU cooler (I did not remove the CPU from the socket every while doing this, so bent pins cannot be the issue) and ever since the new cooler was installed I cannot boot in dual channel mode with my RAM. Pretty frustrating.

I'm about to go exchange the motherboard at the store I purchased it from. Unfortunately I cannot exchange it for a different board, I have to get the same one. Hopefully it works...

FWIW, I did the following to no avail:

-Loosened CPU cooler thinking maybe it was on too tight and it was causing issues with the memory controller since the cooler was the only component that changed between the prior working setup
-Changing timings on my RAM rather than running XMP profile
-Swapped out to completely different RAM, used 2x2GB of OCZ Platinum DDR3-1600 RAM and still no dual channel boot
-Changed between both A1/A2 and B1/B2 channels and neither would boot with either set of RAM
-Called ASUS and they suggested to change RAM timings but otherwise exchange the board

We'll see how today goes after I swap it out...the store is like 30 minutes away so I'm hoping an hour drive (plus exchange time) is the first and last trip I have to make for this.

I have the Gen3 version of this board.
Here are my specs.

Intel i7 2600K @4.2 Ghz
AsusP8Z68-V Pro/Gen3
16GB Corsair Vengeance Blue 1600Mhz RAM @1.5v
HAF X RC-942 black full sized tower
Corsair HX1050
Corsair H80 Liquid Cooler
1x 240Gb OCZ Vertex 3 Sata 600
1x 1TB WD Caviar Black WDFAEX1002
LG SuperMulti Blue BH10LS30
Scythe Kaze Master Pro fan control KM03-BK
2x MSI n580GTX Lightning sli
Windows 7 Ultimate 64bit

I haven't had any problems at all. So far, this is one of the best and easiest to use boards that I've owned.
Also, the V Pro manual should show you how the cpu is correctly installed. So you can line it up properly, and more specifically so the pins don't end up bent. If it isn't explained, here are a few easy steps to follow to get you through it. Take care before touching anything, and ground yourself. Don't put any components on a rug, or cloth. Set them on the antistatic bag that they come with. Anyway, 1st, you unlock and open the metal bracket. 2nd, you remove the plastic cover inside the bracket. 3rd, you hold the CPU so the writing is facing you, the arrow on the corner edge should face the bottom left corner of the CPU, and the 2 indentations on the cpu should line up with the board at that point. They won't line up if the Cpu is in the wrong position. Those pins will bend, if you place it in any other position. Just be sure of the position before you attempt to place it. Also, don't touch the pins or the part of the CPU that connects to the pins with your hands. The slightest pressure against or static touching those areas can damage them. After being properly placed, you can carefully close and lock the bracket.
Also, do your best not to touch the board capacitors. Try not to drop screws on the mainboard, or tighten the mainboard screws too much. As far as your cooler goes, there is a professional video on youtube that shows you how to correctly install the H80/H100 cooler. So, you don't damage any other components.
Next.The RAM installation can be tricky sometimes. You should be using the 2nd slot from the left and the 4th slot. Open the lock, and carefully push the RAM into place. Take care that the RAM is not on an angle and that it is pushed firmly and evenly, but not roughly. If you try to rush it and press too hard, you will damage the RAM or the mainboard and possibly both. I only say this, because you already sent one mainboard back, and I'm sure you don't want to do it again. Here is one last note for the RAM installation. If you install 1600Mhz RAM you may need to manually change the memory settings in the advanced mode from auto to 1600Mhz@1.5v, because the default setting in auto is set to 1333Mhz@1.5v. Once you have the memory installed, working, and set properly, try not to change it again. You don't want to risk damaging them by taking them out and putting them back in multiple times.

Anyway, after reading everything above, it is best that you sent the mainboard back, because you couldn't rule out any other damage to the mainboard at that point. Unless the RAM or the new CPU were damaged during installation on the last board, they should work, when the new board comes. Good luck with the new board.

The pins on modern Intel socket boards are very delicate. More so than past platforms. Utmost care is needed.

This topic has been closed by Proximon